Three-dimensional finite element analysis of cement flow in abutment margin-crown platform switching / 北京大学学报(医学版)

OBJECTIVE@#To analyze the cement flow in the abutment margin-crown platform switching structure by using the three-dimensional finite element analysis, in order to prove that whether the abutment margin-crown platform switching structure can reduce the inflow depth of cement in the implantation adhesive retention.@*METHODS@#By using ANSYS 19.0 software, two models were created, including the one with regular margin and crown (Model one, the traditional group), and the other one with abutment margin-crown platform switching structure (Model two, the platform switching group). Both abutments of the two models were wrapped by gingiva, and the depth of the abutment margins was 1.5 mm submucosal. Two-way fluid structure coupling calculations were produced in two models by using ANSYS 19.0 software. In the two models, the same amount of cement were put between the inner side of the crowns and the abutments. The process of cementing the crown to the abutment was simulated when the crown was 0.6 mm above the abutment. The crown was falling at a constant speed in the whole process spending 0.1 s. Then we observed the cement flow outside the crowns at the time of 0.025 s, 0.05 s, 0.075 s, 0.1 s, and measured the depth of cement over the margins at the time of 0.1 s.@*RESULTS@#At the time of 0 s, 0.025 s, 0.05 s, the cements in the two models were all above the abutment margins. At the time of 0.075 s, in Model one, the gingiva was squeezed by the cement and became deformed, and then a gap was formed between the gingiva and the abutment into which the cement started to flow. In Model two, because of the narrow neck of the crown, the cement flowed out from the gingival as it was pressed by the upward counterforce from the gingival and the abutment margin. At the time of 0.1 s, in Model one, the cement continued to flow deep inside with the gravity force and pressure, and the depth of the cement over the margin was 1 mm. In Model two, the cement continued to flow out from the gingival at the time of 0.075 s, and the depth of the cement over the margin was 0 mm.@*CONCLUSION@#When the abutment was wrapped by the gingiva, the inflow depth of cement in the implantation adhesive retention can be reduced in the abutment margin-crown platform switching structure.

Prótese overdenture: sistema o'ring / Overdenture prosthesis: o'ring system

Overdenture é uma prótese total que se caracteriza por usar apoios retentivos para que aumente sua estabilidade e retenção na cavidade bucal, gerando assim menor desconforto ao paciente e melhor adaptação. A Prótese overdenture dentossuportada necessita de elementos dentais remanescentes com canais tratados endodonticamente e que possuam suporte periodontal adequado. O objetivo deste relato de caso clínico é expor a sequência de confecção de uma prótese overdenture dentossuportada maxilar associada a uma prótese total convencional mandibular, com os passos clínicos detalhados por meio de uma abordagem teórica e visual. Esse tipo de reabilitação favorece a adaptação do paciente à nova condição, visto que o uso de próteses totais convencionais pode causar certo desconforto ao paciente devido à falta de retenção e estabilidade. Essa manutenção dos dentes remanescentes favorece à manutenção óssea e a futura decisão do paciente em optar pela instalação de implantes dentários, podendo confeccionar próteses implantorretidas (overdentures) ou implantossuportadas (protocolo).O Paciente demonstrou-se satisfeito com o resultado estético e funcional após a instalação da prótese concretizando que o tratamento é viável(AU)

Overdenture is a denture that utilizing retentive supports for increase stability and retention in oral cavity. The tooth-supported overdenture require dental elements with root canal therapy and good periodontal support. The aim of this study is to report the confection of a maxillary tooth-supported overdenture associated with mandibular denture and your clinical steps. This rehabilitation promotes the patient's adaptation the new condition, since the use of conventional dentures may cause discomfort due to lack of retention and stability. The preservation of dental elements promotes bone maintenance and forthcoming decision of the patient in the installation of dental implants that can choose implantretained or implant-supported prosthesis. Patient was satisfied with aesthetic and functional result after installation of prosthesis(AU)

Avaliação do tipo de retenção e o uso de diferentes intermediários na adaptação de próteses unitárias sobre implantes / Evaluation of the type of retention and the use of different abutments in the adaptation of single prostheses on implants

Atualmente, devido a perda do elemento dentário e a procura por um tratamento estético e principalmente funcional, a reabilitação com próteses sobre implante tem sido amplamente empregada, com elevada previsibilidade a longo prazo. Com isso, muito tem sido relatado na literatura acerca das possíveis complicações dessa modalidade de tratamento, principalmente relacionado às possibilidades de falhas mecânicas das próteses implantossuportadas. Por isso, o objetivo do presente projeto foi avaliar a influência na adaptação marginal e interna, da utilização do intermediário protético e do tipo de retenção das próteses (parafusada e cimentada) em implantes cone morse submetidos à ciclagem mecânica. Foram confeccionados 40 corpos de prova, no qual cada um tinha a presença de um implante, com as dimensões de 4mm de diâmetro e 11,5mm de comprimento cone morse (n = 40). Dessa forma, foi avaliado a influência da utilização do intermediário e dos sistemas de retenção em cada conexão de maneira específica. Metade dos corpos de prova de cada sistema de conexão foram confeccionados em UCLA (n=20, sendo 10 parafusadas e 10 cimentadas), enquanto que a outra metade foi utilizado um intermediário pré-fabricado (Pilar Universal (n=20, sendo 10 parafusadas e 10 cimentadas). Os corpos de prova foram submetidos à ciclagem mecânica submersos em água destilada simulando um tempo clínico de cinco anos. Além disso, foram avaliados quanto ao torque e destorque (N) e adaptação marginal e interna (µm) antes e após a ciclagem mecânica. Os dados provenientes das mensurações foram organizados em tabela em formato Excel (Microsoft Office Excel, Redmond, WA, Estados Unidos) e submetidos ao software SigmaPlot (SigmaPlot, San Jose, CA, EUA) versão 12.0. Todos os dados foram analisados inicialmente com a utilização da estatística descritiva. Em seguida, os dados para intrusão (valores positivos), extrusão (valores negativos), destorque inicial, destorque final, e descimentação foram analisados em relação a distribuição de normalidade (teste Shapiro-Wilk e igualdade de variância) e, posteriormente, foi adotada a Análise de Variância (ANOVA) a um fator (Grupos diferentes materiais: G1 a G4), quando houve normalidade dos dados, o pós teste de Tukey foi adotado para as comparações múltiplas, quando não foi identificado uma distribuição normal, empregou-se o teste de Kruskall-Wallis e pós-teste de Dunn's ou Tukey, semelhantemente foi realizada a análise específica das variáveis pilares (UCLA e Pilar Universal) e sistemas de retenção (Parafusado e Cimentado). Para todos os testes aplicou-se nível de significância de 5% (α=0,05). A análise gráfica foi considerada através de um gráfico de barras para os dados que apresentaram normalidade com valores de média e desvio padrão, e as demais análises que não apresentaram normalidade foi considerado a confecção de um boxplot para cada grupo comparativo. As próteses sobre implante utilizando pilares em zircônia tem ganhado cada vez mais espaço, além do estudo in vitro, foi realizada uma revisão sistemática para comparar a perda óssea marginal e as complicações próteticas de reabilitações utilizando pilares de zircônia cimentado e parafusado. Em relação as próteses cimentadas e parafusadas, devido as evidências conflitantes e a presença de muitas revisões sistemáticas sobre o tema, foi realizada uma overview de revisões sistemáticas, com o objetivo de compilar as informações disponiveis e avaliar a qualidade metodologica desses estudos a respeito das complicações presentes nas próteses sobre implante cimentadas ou parafusadas(AU)

Currently, due to the loss of the dental element and the search for an aesthetic and mainly functional treatment, rehabilitation with implant prostheses has been widely used, with high long-term predictability. Thus, much has been reported in the literature about the possible complications of this treatment modality, mainly related to the possibility of mechanical failure of implant-supported prostheses. Therefore, the objective of the present project was to evaluate the influence on the marginal and internal adaptation, the use of the prosthetic intermediate and the type of retention of the prostheses (screwed and cemented) in morse taper implants submitted to mechanical cycling. 40 specimens were made, in which each one had an implant, with dimensions of 4 mm in diameter and 11.5 mm in length (n = 40). In this way, the influence of the use of intermediaries and retention systems in each connection was evaluated in a specific way. Half of the specimens of each connection system were made in UCLA (n=20, being 10 screwed and 10 cemented), while the other half was used a prefabricated intermediate (Universal Abutment (n=20, being 10 screwed) and 10 cemented). The specimens were submitted to mechanical cycling submerged in distilled water simulating a clinical time of five years. In addition, they were evaluated for torque and detorque (N) and marginal and internal adaptation (µm) before and after mechanical cycling. Data from measurements were organized in a table in Excel format (Microsoft Office Excel, Redmond, WA, USA) and submitted to SigmaPlot software (SigmaPlot, San Jose, CA, USA) version 12.0. All data were initially analyzed using descriptive statistics. Then, data for intrusion (positive values), extrusion (negative values), initial detorque, final detorque, and debonding were analyzed in relation to dist determination of normality (Shapiro-Wilk test and equality of variance) and, later, the one-way Analysis of Variance (ANOVA) was adopted (Different material groups: G1 to G4), when there was normality of the data, the Tukey post test was adopted for multiple comparisons, when a normal distribution was not identified, the Kruskall-Wallis test and Dunn's or Tukey post-test were used, similarly the specific analysis of the pillar variables (UCLA and Universal Pillar) and systems retainer (Screwed and Cemented). For all tests, a significance level of 5% (α=0.05) was applied. The graphical analysis was considered through a bar graph for the data that presented normality with mean and standard deviation values, and the other analyzes that did not present normality was considered the creation of a boxplot for each comparative group. Implant prostheses using zirconia abutments have gained more and more space, in addition to the in vitro study, a systematic review was performed to compare marginal bone loss and prosthetic complications of rehabilitations using cemented and screwed zirconia abutments. Regarding cemented and screw-retained prostheses, due to conflicting evidence and the presence of many systematic reviews on the subject, an overview of systematic reviews was performed, with the objective of compiling the available information and evaluating the methodological quality of these studies regarding complications present in cemented or screw-retained implant prostheses(AU)

Application evaluation of prefabricated rigid connecting bar in implants immediate impression preparation of edentulous jaw / 北京大学学报(医学版)

OBJECTIVE@#To compare the operation complexity and accuracy of traditional splint impression technique and impression technique with prefabricated rigid connecting bar system for full-arch implants-supported fixed protheses in vitro.@*METHODS@#Standard mandibular edentulous model with six implant analogs was prepared. The implants were placed at the bone level and multiunit abutments screwed into the implants. Two impression techniques were performed: the traditional splint impression technique was used in the control group, and the rigid connecting bar system was used in the test group. In the control group, impression copings were screwed into the multiunit abutments and connected with autopolymerizing acrylic resin. Open tray impression was fabricated with custom tray and polyether. In the test group, cylinders were screwed into the multiunit abutments. Prefabricated rigid bars with suitable length were selected and connected to the cylinders with small amount of autopolymerizing acrylic resin, and open tray impression was obtained. Impression procedures were repeated 6 times in each group. The working time of the two impression methods were recorded and compared. Analogs were screws into the impressions and gypsum casts were poured. The gypsum casts and the standard model were transferred to stereolithography (STL) files with model scanner. Comparative analysis of the STL files of the gypsum casts and the standard model was carried out and the root mean square (RMS) error value of the gypsum casts of the control and test groups compared with the standard model was recorded. The trueness of the two impression techniques was compared.@*RESULTS@#The work time in the test group was significantly lower than that in the control group and the difference was statistically significant [(984.5±63.3) s vs. (1 478.3±156.2) s, P < 0.05]. Compared with the standard model, the RMS error value of the implant abutments in the test group was (16.9±5.5) μm. The RMS value in the control group was (20.2±8.0) μm. The difference between the two groups was not significant (P>0.05).@*CONCLUSION@#The prefabricated rigid connecting bar can save the chair-side work time in implants immediate loading of edentulous jaw and simplify the impression process. The impression accuracy is not significantly different from the traditional impression technology. The impression technique with prefabricated rigid connecting bar system is worthy of clinical application.

Tasa de supervivencia de prótesis fija unitaria de cerámica feldespática y feldespática reforzada / Survival rate of feldspathic and reinforced feldspathic ceramic single-unit fixed prostheses

Introducción: Gracias a su eficiencia y al uso exclusivo de cerámicas libres de metal, en rehabilitación oral se ha logrado alcanzar los estándares estéticos y mecánicos, manteniendo o, incluso, superando, la calidad de los tratamientos en comparación con las restauraciones metal cerámicas tradicionales. Actualmente los mecanismos de confeccion de cerámica libre están evolucionando cada vez mas hacia las tecnologías maquinadas CAD-CAM y disminuyendo su producción mediante la técnica de Inyeccion PRESS. Objetivo: Comparar la tasa de supervivencia de prótesis fija unitaria realizadas con cerámicas feldespáticas convencionales y reforzadas con disilicato de litio, confeccionadas con sistema CAD/CAM de CEREC® chair-side, en comparación con el método de inyección de laboratorio PRESS convencional de prensión. Métodos: Revisión sistemática realizada a través de búsqueda de evidencia científica en PubMed, PubMed Clinical Queries, Epistemónikos, Tripdatabase, Cochrane Library, recursos electrónicos de la Universidad de los Andes y bibliografía retrógrada, de artículos publicados hasta el año 2019. Se incluyeron todos aquellos estudios referentes a prótesis fija unitaria de cerámicas feldespática convencional y feldespática reforzada con disilicato de litio, confeccionadas mediante CAD/CAM y/o método convencional. Resultados: Un total de 28 artículos cumplieron los criterios de inclusión: 21 estudios observacionales de cohorte, 4 ensayos clínicos aleatorizados y 3 no aleatorizados. A corto y mediano plazo, CAD/CAM de CEREC® registró tasas de supervivencia de 98 por ciento y 91,9 por ciento, respectivamente. El sistema convencional registró tasas de supervivencia de 97,5 por ciento a corto plazo y 93 por ciento a mediano. Conclusiones: A corto plazo se describe en la literatura que CAD/CAM de CEREC® tuvo una tasa de supervivencia ligeramente superior al sistema convencional. Por otro lado, a mediano plazo CAD/CAM de CEREC® presentó una leve disminución respecto al sistema convencional. Aún no hay estudios disponibles para determinar la supervivencia clínica de los tratamientos a largo plazo(AU)

Introduction: Thanks to its efficiency and the exclusive use of metal-free ceramics, in oral rehabilitation it has been possible to achieve aesthetic and mechanical standards, maintaining or even exceeding the quality of the treatments compared to traditional metal-ceramic restorations. Currently, free ceramic manufacturing mechanisms are increasingly evolving towards CAD-CAM machined technologies and decreasing their conventional production through the PRESS Injection technique. Objective: Compare the survival rate of single-unit fixed prostheses made with conventional feldspathic ceramics and reinforced with lithium disilicate by the CEREC® CAD/CAM chairside system, with the conventional PRESS laboratory injection method. Methods: A systematic review was conducted of scientific evidence included in papers published until the year 2019 in PubMed, PubMed Clinical Queries, Epistemonikos, Tripdatabase, Cochrane Library, electronic resources of Los Andes Peruvian University, and retrograde bibliography. The papers selected dealt with conventional and lithium-disilicate reinforced feldspathic ceramic single-unit prostheses made by CAD/CAM and/or the conventional method. Results: A total 28 papers met the inclusion criteria. Of these, 21 were observational cohort studies, four were randomized clinical assays and three were non-randomized assays. Short- and mid-term, CEREC® CAD/CAM achieved survival rates of 98 percent and 91.9 percent, respectively. The conventional system achieved survival rates of 97.5 percent short-term and 93 percent mid-term. Conclusions: As described in the literature, CEREC® CAD/CAM had a slightly higher survival rate than the conventional system in the short term. In the medium term, however, CEREC® CAD/CAM displayed a slight reduction in comparison with the conventional system. No studies are available to determine the clinical survival of the treatments in the long term(AU)

Screwed and cement implant prosthesis: current clinical considerations / Prótese sobre implante cimentada e parafusada: considerações clínicas atuais

ABSTRACT Introduction: There is no consensus as to which cemented or screwed retention system is best to avoid bone loss around the implant from a fixed implant-supported restoration. Objective: To evaluate the prosthesis retention systems on screw and cemented implants, regarding: bone loss, survival and failure rate, biological complications and microbiological analysis. Methods: A search was made for scientific articles that contemplated the subject through the databases Pubmed and SciELO, without period restriction. The titles, abstracts and then access to the full text has been verified. Results: It was found that excess cement may play an important role in the development of peri-implant disease. Technical failures are most seen in prosthesis retained by screws, and biological complications in cemented crowns. The success rate for both restraint systems is high, and retention-independent implant prosthesis treatment provides predictability. Conclusion: The appropriate retention system for the patient depends on several factors, including indication, advantages and disadvantages, retention provided, aesthetics and clinical performance.

RESUMO Introdução: Não há consenso sobre qual sistema de retenção, cimentado ou parafusado, é o melhor para evitar perda óssea ao redor do implante de uma restauração fixa implanto-suportada. Objetivo: Avaliar os sistemas de retenção de próteses sobre implantes parafusadas e cimentadas, quanto aos fatores: perda óssea, taxa de sobrevivência e de falhas, complicações biológicas e análises microbiológicas. Métodos: Foi realizada uma busca por artigos científicos que contemplassem o tema através das bases de dados Pubmed e SciELO, sem restrição de período. Os títulos, resumos e em seguida o acesso ao texto completo foi verificado. Resultados: Foi observado que o excesso de cimento pode desempenhar um papel importante no desenvolvimento da doença peri-implantar. Falhas técnicas são mais observadas em próteses retidas por parafusos e complicações biológicas em coroas cimentadas. A taxa de sucesso para os dois sistemas de retenção é alta e o tratamento com próteses sobre implantes independente da retenção oferece previsibilidade ao caso. Conclusão: O sistema de retenção apropriado para o paciente depende de diversos fatores, incluindo a indicação, vantagens e desvantagens, retenção fornecida, estética e desempenho clínico.

Estudo in vitro da influência de diferentes plugs coronários sobre o remanescente da obturação, após preparo para pino, na retenção de pinos metálicos fundidos / In vitro assessment of the influence of different protection plugs over obturation remnant space, after post preparation, on the retention of cast metal posts

Objetivo: Avaliar a influência de diferentes plugs de proteção, acomodados sobre o remanescente da obturação após preparo para pino, na retenção de pinos metálicos fundidos. Métodos: Cinquenta dentes bovinos foram decoronados, manualmente instrumentados até a lima manual Kerr #80 e obturados. A desobturação parcial de 10mm do conduto foi realizada com uma broca Largo e os grupos foram divididos de acordo com os diferentes materiais utilizados como plugs (n=10): Grupo I (Controle, sem plug); Grupo II (plug de Coltosol®); Grupo III (plug, em consistência de massa, de Sealapex® + óxido de zinco); Grupo IV (plug de etil-cianoacrilato); e Grupo V (plug de fosfato de zinco). Uma camada de 1mm de espessura dos diferentes plugs (Grupos II, III, IV ou V) foi acomodada sobre a obturação remanescente. Os espécimes foram selados e armazenados em 100% de umidade, por 7 dias. Após moldagem do conduto, foram confeccionados pinos metálicos fundidos e cimentados com fosfato de zinco. Os espécimes permaneceram em câmara úmida por 45 dias antes do teste de tração, realizado em uma máquina universal de ensaios. Os valores foram expressos em Mega pascal (MPa) e submetidos aos testes ANOVA e Tukey (p<0,05). Resultados: O etilcianoacrilato diminuiu a retenção dos pinos metálicos fundidos (p<0,01). Não houve diferença entre os outros grupos (p>0,05), semelhante- mente ao controle. Conclusão: A proteção da obturação com plugs confeccionados com etil-cianoacrilato prejudica a retenção de pinos metálicos fundidos cimentados com fosfato de zinco, enquanto Sealapex® acrescido de óxido de zinco, fosfato de zinco endurecido ou Coltosol® não interferem na adesividade (AU).

A new retaining method of cement-retained restoration with linguo-horizontal insertion of fiber post / 대한치과보철학회지

The retaining methods of implant prosthesis were classified into a screw-retained and a cement-retained type. A screw-retained prosthesis has many advantages, such as retrievability, preventing residual cement, while their disadvantages include the possibility of screw loosening and fracture, on the contrary advantages of cement-retained prosthesis are relatively low cost, but they are difficult to retrieve. To combine the advantages of both type, screw-cement retained prosthesis (SCRP) type have been introduced. But they still require ideal implant placement. So we introduce fiber post retained prosthesis without residual cement for preventing soft tissue trouble due to excessive cement.

Masticatory performance with different types of rehabilitation of the edentulous mandible

Abstract Aim: To compare the masticatory performance associated with different rehabilitation strategies for patients with edentulous mandibles. Methods: one portion of the test food "Optocal" was provided to groups: Natural Dentition (n = 15), Mandibular Fixed Implant-Supported Prosthesis with Maxillary Fixed Prosthesis (n = 8), Mandibular Fixed Implant-Supported Prosthesis with Maxillary Removable Prosthesis (n = 14), Mandibular Implant-Retained Overdenture with Maxillary Removable Prosthesis (n = 16), and Complete Dentures (n = 16). The portion was collected after 40 chewing strokes, and then passed through a stack of eight sieves with decreasing apertures. Masticatory performance was determined by weighing the portion of food on each sieve. Results: the masticatory performance was: 71.00% for Natural Dentition, 41.57% for Mandibular Fixed Implant-Supported Prosthesis with Maxillary Fixed Prosthesis, 31.44% for Mandibular Fixed Implant-Supported Prosthesis with Maxillary Removable Prosthesis, 27.70% for Mandibular Implant-retained Overdenture, and 14.33% for Complete Dentures. The data were statistically compared using Student's t-test (p < 0.05). Natural Dentition and Complete Denture groups were statistically different from all other groups, with the Natural Dentition and Complete Denture groups exhibiting the highest and lowest masticatory performance values, respectively. Conclusions: Osseointegrated implants improved the masticatory performance of all implant-supported groups compared to the Complete Dentures group.

Correlation between clinical performance and degree of conversion of resin cements: a literature review

AbstractResin-based cements have been frequently employed in clinical practice to lute indirect restorations. However, there are numerous factors that may compromise the clinical performance of those cements. The aim of this literature review is to present and discuss some of the clinical factors that may affect the performance of current resin-based luting systems. Resin cements may have three different curing mechanisms: chemical curing, photo curing or a combination of both. Chemically cured systems are recommended to be used under opaque or thick restorations, due to the reduced access of the light. Photo-cured cements are mainly indicated for translucent veneers, due to the possibility of light transmission through the restoration. Dual-cured are more versatile systems and, theoretically, can be used in either situation, since the presence of both curing mechanisms might guarantee a high degree of conversion (DC) under every condition. However, it has been demonstrated that clinical procedures and characteristics of the materials may have many different implications in the DC of currently available resin cements, affecting their mechanical properties, bond strength to the substrate and the esthetic results of the restoration. Factors such as curing mechanism, choice of adhesive system, indirect restorative material and light-curing device may affect the degree of conversion of the cement and, therefore, have an effect on the clinical performance of resin-based cements. Specific measures are to be taken to ensure a higher DC of the luting system to be used.

Parafusamento transverso em prótese sobre implante: aspectos inovadores no design e na aplicação do sistema / Cross-pinning in implant-supported prosthesis: innovative design and approach

Reabilitações com próteses implantossuportadas são usadas frequentemente para resolver casos de edentulismo. Elas podem ser retidas por de meio de parafusos ou agentes de cimentação. No entanto, nos casos de alinhamento inadequado dos implantes ou fragilidade pelo desenho final da estrutura protética, o sistema de parafusamento convencional não pode ser utilizado. Um método alternativo para se manter a reversibilidade da peça protética é o parafusamento transverso. Este consiste em um sistema tubo/parafuso de dimensões reduzidas que possibilita o parafusamento em uma área palatina ou lingual. Entretanto, aperfeiçoamentos nos sistemas existentes comercialmente eram necessários para se suprirem dificuldades como custo, técnica de confecção e dimensões dos componentes. O presente artigo apresenta o desenvolvimento de um produto adequado para este método, para suprir as desvantagens dos sistemas anteriores, apresenta a técnica de confecção clínica e laboratorial, e discute os aspectos fundamentais no planejamento desse sistema...

Implant-supported prostheses are frequently used in oral rehabilitation to solve cases of edentulism. They may be screw-retained or cement-retained. However, sometimes conventional screw-retained systems can not be used in cases of improper alignment of implants or compromised structural integrity of the prosthesis. An alternative method to maintain reversibility of the rehabilitation is cross-pinning. This system consists of a tube/screw with reduced dimensions which enables screwing in a palatal or lingual area. However, improvements in the commercially existing systems have been necessary to overcome difficulties such as costs, manufacturing technique and component dimensions. This paper presents the development of an appropriate product for this method, allowing to overcome the disadvantages of previous systems and analyzes the clinical and laboratory steps discussing the fundamental aspects of planning when using this system...

Clinical common problems after restoration with telescopic crown-retained removable partial dentures / 中国组织工程研究

BACKGROUND:Telescopic crown-retained removable partial dentures are characterized as pick to wear voluntarily, convenient to clean, smal foreign body sensation of the fixed denture, and good functional recovery, and have been widely used in recent years. However, there are also some problems existing. OBJECTIVE:To review the common problems of the telescopic crown-retained removable partial dentures and to raise the countermeasures. METHODS: A computer-based search of CNKI and PubMed (1980-2013) was performed for relevant articles addressing the telescopic crown using the keywords of “cone sleeve crown, abutment, clinical observation” in Chinese and English, respectively. RESULTS AND CONCLUSION:Telescopic crown-retained removable partial dentures are an ideal method for repair of dentition defects associated with periodontal disease. In summary, the telescopic crown-retained removable partial dentures have good clinical effects, but how to maintain the long-term stability is the main chalenge. In recent years, a variety of ways have been developed to improve the long-term stability, such as changing the inner crown material, which obtains the most prominent achievements, but these methods need to be further observed in clinical applications. Common complications for telescopic crown-retained removable partial dentures include abutment fracture, inner crown shedding, denture fracture, periodontal problems, and reduced retention force, which generaly cannot influence the application of telescopic crown-retained removable partial dentures through repair.

Loosening torque of Universal Abutment screws after cyclic loading: influence of tightening technique and screw coating

PURPOSE: The purpose of this study was to evaluate the influence of tightening technique and the screw coating on the loosening torque of screws used for Universal Abutment fixation after cyclic loading. MATERIALS AND METHODS: Forty implants (Titamax Ti Cortical, HE, Neodent) (n=10) were submerged in acrylic resin and four tightening techniques for Universal Abutment fixation were evaluated: A - torque with 32 Ncm (control); B - torque with 32 Ncm holding the torque meter for 20 seconds; C - torque with 32 Ncm and retorque after 10 minutes; D - torque (32 Ncm) holding the torque meter for 20 seconds and retorque after 10 minutes as initially. Samples were divided into subgroups according to the screw used: conventional titanium screw or diamond like carbon-coated (DLC) screw. Metallic crowns were fabricated for each abutment. Samples were submitted to cyclic loading at 106 cycles and 130 N of force. Data were analyzed by two-way ANOVA and Tukey's test (5%). RESULTS: The tightening technique did not show significant influence on the loosening torque of screws (P=.509). Conventional titanium screws showed significant higher loosening torque values than DLC (P=.000). CONCLUSION: The use of conventional titanium screw is more important than the tightening techniques employed in this study to provide long-term stability to Universal Abutment screws.

Maxillary complete denture rehabilitation of a patient with marked maxillomandibular discrepancy: a clinical case report / Confecção de prótese total superior em paciente com acentuada discrepância maxilomandibular: relato de caso clínico

Dentistry is constantly concerned with enabling better living conditions for patients, as well as providing comfort so that functions such as chewing, speaking, and swallowing may be executed properly and esthetically satisfactory. In edentulous patients, many of these functions are lost, but can be restored by prosthodontics. Within this context, the present article seeks to report a clinical case in which a maxillary complete denture was made for a patient presenting with maxillomandibular discrepancy and marked maxillary prognathism.

Uma constante preocupação da odontologia é de possibilitar melhores condições de vida aos pacientes, oferecendo-lhe conforto para que funções como mastigação, fonação e deglutição possam ser exercidas de maneira adequada e que apresente uma estética satisfatória. Com a perda dentária, muitas destas funções são perdidas, mas podem ser restabelecidas através do uso de prótese. Neste contexto, o presente artigo visa descrever a execução de um caso clínico onde foi confeccionada uma prótese total superior em paciente com discrepância maxilomandibular apresentando projeção acentuada da maxila em relação à mandíbula.

Utilização de parafusos linguais para fixação de prótese total inferior sobre implantes com carga imediata: relato de caso clínico / Lingual use of screws for attaching a mandibular fixed prosthesis to implants with immediate loading: case report

O tratamento reabilitador que utiliza próteses fixas implantossuportadas soluciona as deficiências dentárias maxilomandibulares com real sucesso. O tratamento proposto inicialmente por Branemark em dois estágios cirúrgicos está sofrendo sucessivas modificações e aperfeiçoamentos, no intuito de diminuir o tempo de instalação das próteses sobre implantes, existindo, em alguns casos, a possibilidade de se reabilitar pacientes imediatamente após a instalação dos implantes. Nesse sentido, vários estudos sobre a carga imediata têm sido frequentemente realizados, e devidamente documentados na literatura, para a solução dos casos envolvendo próteses totais fixas sobre implantes osseointegráveis. Em decorrência da reabsorção do rebordo alveolar maxilomandibular pós-extração, a utilização de componentes protéticos angulados é uma opção para a correção da posição de implantes vestibularizados. Este trabalho tem como objetivo apresentar um caso clínico de implantes do tipo Cone-Morse, imediatos, instalados em região anterior de mandíbula, com a confecção de uma prótese total inferior com carga imediata, utilizando-se um sistema de fixação tipo tubo-parafuso como forma de substituição aos pilares angulados.

The rehabilitative treatment that uses fixed prosthesis with dental implants addresses the dental maxillomandibular deficiencies with real success. The treatment initially proposed by Branemark in two surgical stages is undergoing successive modifications and improvements in order to reduce the installation time of the prostheses on implants, in some cases there is an opportunity to rehabilitate the patient immediately after implant placement. Accordingly, several studies on immediate loading have been frequently performed and documented in the literature for the solution of cases involving fixed prostheses on osseointegrated implants. As a result of resorption of the alveolar maxillomandibular post-extraction, the use of angulated abutments is an option for the correction of the position of implants. This paper aims to present a case report of immediate implants with Cone-Morse platform. placed in the anterior mandible and making a mandibular fixed prosthesis with immediate loading in which was used a fixed screw-type tube as a way to replace angled abutments.

Coroas cimentadas em implantes de conexão sem parafuso / Cemented crowns in screwless implant connection

A reabilitação protética de implantes por meio de coroas cimentadas é um tema controverso, uma vez que problemas, como a remoção dos excessos de cimento e o acesso ao parafuso do munhão, são descritos na literatura. O objetivo deste trabalho é avaliar, por meio de um caso clínico, a utilização de coroas cimentadas sobre implante com conexão do tipo locking taper na reabilitação protética em região posterior de mandíbula. A conexão locking taper consiste em uma conexão cônica com inclinação de 1 a 1,5º entre o munhão e o implante, sem parafuso, unidos friccionalmente por uma soldadura fria entre metais. A ausência de parafuso torna a conexão locking taper versátil porque possibilita uma cimentação extrabucal das coroas metalocerâmicas nos munhões e inserção do conjunto coroa-munhão livre de excessos de cimento no implante. Selamento bacteriano, estabilidade óssea peri-implantar e redução do número de componentes protéticos são vantagens dessa conexão protética. Concluímos que coroas unitárias cimentadas em implantes locking taper oferecem uma boa opção de tratamento para o edentulismo parcial, no entanto mais estudos são necessários.

The prosthetic rehabilitation with cemented crowns in oral implants is a controversial topic, since problems like removing luting excess and accessing the abutment screw are described in the literature. The aim of this article is to evaluate, through a c1inical case, the application of locking taper implant cemented crowns in posterior mandibular area. Locking taper consists of a screwless 1-1.5° morse taper connection among abutment and implant, united by a frictional cold welding. The screwless quality makes locking taper versatile because it allows an extraoral luting of metaloceramic crowns in implant abutments and insertion of integrated abutment-crown without luting excess in oral implants. Bacterial sealing, bone stability around the implant, reduction in prosthetic components are advantages of this prosthetic connection. The authors concluded that single cemented crowns in locking taper implants offers a good treatment option for partial edentulism, but further studies are suggested.

Influence of retention-form design on the retention of resin-bonded fixed partial dentures / 北京大学学报(医学版)

Objective: To evaluate the influence of retention-form design of resin bonded fixed partial dentures(RBFPDs). Methods: Forty-five metal replicas of posterior metal RBFPDs were divided into 3 groups(n=15):C shape(control group), C shape + axial groove, C shape + pin hole. All the replicas were luted with Panavia F cement and subgroup of 5 specimens were subject to 70 N compressive load cycling for 0 cycles, 240 000 cycles , and 1 200 000 cycles respectively .Half of the cycles was on the central fossa of the pontics and half on the buccal inclined surface of the lingual cusp. Forces for dislodgment of the specimens were applied along the long axis of the abutment at a crosshead speed of 1.0 mm /min. The separation forces were recorded as maxium retention force at the time of dislodgement. Results: Se-paration forces of the C shape group (566.82?71.59 N)0.05). After 1 200 000 cycles, the retention force of the RBFPDs decreased significantly (P

Relación entre el uso nocturno y la adaptación a la prótesis estomatológica

La rehabilitación protésica de un paciente conlleva una serie de cambios, que en un tiempo se traducen en todo un proceso adaptativo. Una vez instalada la prótesis en el paciente se le instruye en lo que debe hacer para su mejor adaptación, se le dan indicaciones sobre el uso y cuidado de la prótesis. El uso nocturno de la prótesis constituyó el motor impulsor para nuestro trabajo, en el cual nos dimos a la tarea de relacionar la adaptación con el uso nocturno en cuanto a tiempo de instalada, experiencia protésica anterior, tipo de prótesis y tiempo de uso nocturno. Para su realización se encuestaron a 50 pacientes pertenecientes al consultorio 25 de la Clínica Estomatológica "Manuel Angulo Farrán", con lo cual se evidenció que existe una relación directa entre el uso nocturno y la adaptación favorable a medida que se prolonga el tiempo de uso y de instalada la prótesis, en el paciente que haya tenido experiencia protésica anterior y en los portadores de prótesis totales superiores e inferiores de acrílico.

The prosthetic rehabilitation of a patient leads to a series of changes that are part of an adaptation process. Once the prosthesis is placed, the patient is instructed what to do for a better adaptation and indications are given on the use and care of the prosthesis. The nocturnal use of the prosthesis is the main objective of our paper, in which we related the adaptation to the nocturnal use as regards the time of placement, the previous prosthetic experience, the type of prosthesis and the time of nocturnal use. 50 patients from the physician´s office No. 25 of "Manuel Angulo Farrán" Dental Clinic were surveyed and it was observed that there was a direct relationship between the nocturnal use and the favorable adaptation as the time of placement and use of the prosthesis were longer among those patients with previous prosthetic experience and in those having upper and lower acrylic dental prostheses.